I felt as though I had hit a road block; while Robert’s kind words were encouraging, I felt like there was nothing I could do as an individual to create an end market for clamshells post-consumer, either as non-beverage PET flake or mixed rigid plastic flake. Perhaps on the vehicle of collaboration, we would be able to come up with the quantity necessary to create an end market for this homeless material…
I then started the following discussion on greenerpackage.com:
Where does the plastics industry go from here?
As Sean Sabre pointed out in a recent post, there is no recycling market for non-beverage PET flake i.e. the PET used in thermoformed packages (to veiw this discussion, visit http://www.greenerpackage.com/discuss/recycling/recovery_series_-_topic_2_universal_pet_recyclability_myth).
According to various contacts at Waste Management, this is because those who buy the balled PET beverage containers to recycle into other products do not want PET clams, blisters or components as it compromises the feedstock of the PET bottle flake. In other words, because PET beverage bottles have the same IV, additives and chemical properties, the quantity of that type of material is there, which allows for there to be an end market for it. Contrarily, the PET used in thermoformed packages has different properties depending on the additives used for the specific packaging application i.e. food, medical, consumer goods. Therefore, the quantity of the same type of PET is not available for the creation of an end market for this material. At the same time, however, there is a market for this type of material on the East and West coasts (“non-traditional rigid containers”) because China and other international markets undergoing industrialization buy this material for its stored energy value. In a nut shell: we can’t recycle it if the quantity is not there, which inherently means there is no market for the end life of these types of PET.
Where do we go from here? Do we, as an industry, decide on using one type of material per application i.e. one PET type for food, medical, and consumer goods in order to ensure the quantity of material necessary for the development of an end market for said material? Do we “down-cycle,” via Pyrolysis? Do we switch to PLA or other bio-resins, which require more energy to produce than traditional, fossil-based plastics and require the existence of commercial composting facilities, which are far and few a dozen? As an industry, we must collaborate if we want to reach our shared goals of sustainability.
If interested in the comments to this post, visit http://www.greenerpackage.com/discuss/thermoformed_packaging/where_does_plastic_industry_go_here
Once I reached out to the larger packaging community about my concerns as a packaging professional, I sent the following email to a project manager at the Sustainable Packaging Coalition. As the tone of my above conversation implies, I was hoping that collaboration would begin with member companies of the SPC:
Hey,
Just out of curiosity, do you have any relationship with SPI (Society of the Plastic Industry) or other packaging trade organizations? I have begun a dialogue with said organization in regard to the SPI resin identification numbers and the feasibility of recycling non-beverage PET flake i.e. clamshells, blisters and thermoform components. We are trying to figure out a way to recapture our thermoformed packages, which currently are not recycled. We can’t decide if a closed loop system would be best, as is in the case with electronics and batteries, or if working with the existing recycling infrastructure would be more beneficial.
What is the SPC’s stance on the feasibility of recycling non beverage PET flake? Do you think a project like this would be something of interest for the SPC?
Best,
Chandler
Let’s hope the SPC wants to help! Tune in tomorrow for more exciting happenings in the world of sustainable packaging initiatives!
I then started the following discussion on greenerpackage.com:
Where does the plastics industry go from here?
As Sean Sabre pointed out in a recent post, there is no recycling market for non-beverage PET flake i.e. the PET used in thermoformed packages (to veiw this discussion, visit http://www.greenerpackage.com/discuss/recycling/recovery_series_-_topic_2_universal_pet_recyclability_myth).
According to various contacts at Waste Management, this is because those who buy the balled PET beverage containers to recycle into other products do not want PET clams, blisters or components as it compromises the feedstock of the PET bottle flake. In other words, because PET beverage bottles have the same IV, additives and chemical properties, the quantity of that type of material is there, which allows for there to be an end market for it. Contrarily, the PET used in thermoformed packages has different properties depending on the additives used for the specific packaging application i.e. food, medical, consumer goods. Therefore, the quantity of the same type of PET is not available for the creation of an end market for this material. At the same time, however, there is a market for this type of material on the East and West coasts (“non-traditional rigid containers”) because China and other international markets undergoing industrialization buy this material for its stored energy value. In a nut shell: we can’t recycle it if the quantity is not there, which inherently means there is no market for the end life of these types of PET.
Where do we go from here? Do we, as an industry, decide on using one type of material per application i.e. one PET type for food, medical, and consumer goods in order to ensure the quantity of material necessary for the development of an end market for said material? Do we “down-cycle,” via Pyrolysis? Do we switch to PLA or other bio-resins, which require more energy to produce than traditional, fossil-based plastics and require the existence of commercial composting facilities, which are far and few a dozen? As an industry, we must collaborate if we want to reach our shared goals of sustainability.
If interested in the comments to this post, visit http://www.greenerpackage.com/discuss/thermoformed_packaging/where_does_plastic_industry_go_here
Once I reached out to the larger packaging community about my concerns as a packaging professional, I sent the following email to a project manager at the Sustainable Packaging Coalition. As the tone of my above conversation implies, I was hoping that collaboration would begin with member companies of the SPC:
Hey,
Just out of curiosity, do you have any relationship with SPI (Society of the Plastic Industry) or other packaging trade organizations? I have begun a dialogue with said organization in regard to the SPI resin identification numbers and the feasibility of recycling non-beverage PET flake i.e. clamshells, blisters and thermoform components. We are trying to figure out a way to recapture our thermoformed packages, which currently are not recycled. We can’t decide if a closed loop system would be best, as is in the case with electronics and batteries, or if working with the existing recycling infrastructure would be more beneficial.
What is the SPC’s stance on the feasibility of recycling non beverage PET flake? Do you think a project like this would be something of interest for the SPC?
Best,
Chandler
Let’s hope the SPC wants to help! Tune in tomorrow for more exciting happenings in the world of sustainable packaging initiatives!